10. Epoxy is a mass and temperature sensitive material. MAS Table Top Pro ,MAS Penetrating Epoxy Sealer and MAS Deep Pour. If depths thicker than 1/8”- 1/4" are desired, multiple coats are necessary. Can I stir it with a popsicle stick? If you want to eliminate some time, you can always take a power drill with the mixing attachments. Rob: Wow. Derek: We can go ahead and wave it over and it'll turn into like glass. Derek: Again, just to be safe and not be able to get epoxy all over the place, you want to usually just put it in very slowly and then slowly start, and make sure you're really working around the edges and on the bottom. Some people become sensitized to the epoxy resin and others to the hardener. Simply put you can smell it, but it contains no solvents, so you won’t have a strong solvent odor fill your work space. Overcoating with a thin layer of fresh epoxy, or buffing and polishing. MAS Table Top Pro is considered a 100% solids epoxy coating. Derek: No, you can't overmix, but with other systems like one-to-one, if you were to pour this much epoxy in this large of a quantity, and you were to mix too long, eventually the chemicals are going to react and it's where they start to kick off. We typically recommend using MAS Deep Pour epoxy for river tables where you can pour large amounts of epoxy up to 0.5-1” thick, and then using MAS Table Top Pro as the top coat. Epoxy is a mass and temperature sensitive material. Differences in viscosity can also lead to variations in how much waste is being lost after every pour. Only mix up what you intend to immediately use. Marine grade polyurethane varnishes, with UV protection additives, offer improved UV stability and abrasion resistance over “off the shelf” spar varnishes available at hardware stores like Home Depot or Lowes. . We’ve actually tested our product and obtained a result of 1.5 g/L VOC, which is extremely low. We usually recommend like a mica powder or alcohol ink, Mixol's a great example. Mica Powder is. Since MAS Table Top is designed with flood coating and encapsulating applications in mind, as opposed to are more traditional load bearing laminating system or adhesive, I think you’ll be fine overcoating acrylic. That should be around 2-4 hours after pouring. If the mixed material starts to get warm, that’s your last warning the curing reaction is starting to take place and you need to get the epoxy poured onto your surface ASAP. WiseBond ® Deep Pour™ Epoxy cures to a crystal clear appearance or can be tinted with our powdered or liquid pigment colorants. If you do get some on your skin wash it off immediately with soap and water. The whole mixing process shouldn’t take more than 5-6 minutes. Epoxy is a mass and temperature sensitive material. Now we got it level. There are ways to manipulate the system. As a general rule, if you can sand, you should sand. We'll just lug this into a bigger bucket here. Once that sets up and cures, it's basically creating an eggshell barrier to where once you pour the Deep Pour Epoxy any air or moisture left in the wood, it's not going to kick out any bubbles, or foam, or anything like that. Derek: Again, with this system, we designed it to be self-releasing. Calculate Epoxy Coverage Deep Pour™ Epoxy. If the drips have hardened directly to the underside of the project, simply sand or grind away as needed. Be sure the stain is fully dry before coating work with epoxy. Rob: But it's going to flow right over here, isn't it? Tabletop epoxy quantities of 64-128 ounces typically require 5-8 minutes - use a timer. Thin coats and cooler working conditions will cure slower, and thick coats and hotter working conditions will cure faster. While much of the industry will tell you their 100% solids epoxy products contains zero VOC, there could still be trace amounts of VOC present in any epoxy system. To start, the surface must be clean, dry and free of contamination. Deep Pour 2”- 4” Inches Plus! Derek: Sounds good. Best options for managing drips on the underside of project are to either periodically tend and smooth out with a brush as they form or use blue painters tape to protect underside perimeter. Are dyes compatible? The more you mix up, and the warmer it is, the faster it will gel. Do not use paper towels, dirty rags, contaminated sandpaper, or touch surface with oily fingers. A good comparison is the color difference of wet vs dry wood, although the extent of the color change can vary based on wood type. Personally, I’d always start with an epoxy seal coat. If you make a table, its going to take a a lot of energy to warm the area a few degrees so more often than not thermochromics are best used in small items like coasters that can warm up rapidly. Mica comes in a variety of colors and is generally the go to pigment. Rob: Is that good enough? Specialty Epoxies from MAS | Rockler Demonstration - YouTube It's very dense, so a little bit goes a long way just like other mica powders. How do I remove cup rings and heat indents from epoxy resin? Objects that harder than the epoxy, scuff, gouge or scratch the surface if proper care isn’t given. What is the working time for MAS Tabletop Pro? There isn't a set minimum depth because the volume of epoxy could be high but the layer could be thin. You could seal coat your project with the MAS 2:1 Non-blushing system or MAS PES, but we recommend sealing with MAS Table Top so you don’t have to invest in multiple systems to complete one project. Symptoms may include tightening of the throat and difficulty breathing. Not the other way around. The same thing goes for the mixing buckets. When can you pour another layer of MAS Tabletop Pro? 3 Reviews. What is the best temperature to use epoxy resin? Lots of people are really engaged in this new technique. Fill the spot and let it fully cure, hand sand the spot that was just filled. We do recommend just wiping it out with denatured alcohol, just to be safe and make sure everything's-. Once the epoxy start to react, with this system, it's going to be a very long time but if you were to get anything on your hands, you can just wash it off with some denatured alcohol, warm soapy water, and you'll be fine. Rating Review: 4.5 stars out of 5. The max thickness MAS Table Top Pro should be applied is 1/8-1/4” per layer. Derek: Once the resin and the hardener are mixed, we always recommend wearing gloves just because all epoxies are corrosive and it can be hazardous, but we always want to make sure we're being safe, so we always wear gloves. The gel time (time it takes the mixed epoxy resin and hardener to initially harden up) can vary drastically depending on any number of factors such as mixing mass, material temp, ambient temp, mixing time, speed of mixing, speed of application, coating thickness, etc. Mica Powder is commonly used however some customers have experimented with alcohol inks and acrylic tints. DO NOT use a tack cloth. Give it a go. MAS Table Top has 30 minute gel time at 77°F in a 150 gram mass, but will set up much faster if warmer or left sitting for an extended time in a larger mass. Derek: Yes, and then between layers whenever you sand, you always want to wipe down with the denatured alcohol just to make sure your surface is very clean. MAS Epoxies Penetrating Epoxy Sealer is ideal for wood repairs because it adds structural strength and protection against water. Derek: Correct. Each layer MUST be allowed to cool to room temperature (70-80°F) before adding additional layers. The maximum coating thickness of MAS Table Top is 1/8” – 1/4” per pour, but deeper coatings can be achieved by step pouring multiple layers. There’s certainly more than one way to go about this, and a whole lot of polishing compounds and equipment out there to choose from, but here’s a general description of a simple process you could try. It has the consistency of water. It wouldn't hurt to hit it with a heat gun or a torch because that could just eliminate them even more, but for the most part, we designed it to self-release air. The overcoat time can be as short as it takes the previous coat to achieve surface tack. Must be sanded away. Can you make an epoxy resin river table with MAS Tabletop Pro? Wipe surface down with a clean cotton t-shirt rag soaked in an oil free solvent like denatured alcohol prior to applying epoxy seal coat. Small molds can be poured in single layers up to 2 in. MAS Deep Pour Epoxy, TotalBoat ThickSet Epoxy, VersaKast Clear Casting Coating Epoxy, Smooth-On EpoxAcast 690, etc. If for any reason you are not satisfied with the merchandise you ordered, just return it within 90 days to receive a refund in the manner of original payment. Once epoxy has started to harden, you can just carefully peel the tape and any drips away before if fully sets. DO NOT deviate in an attempt to speed up or slow down the gel time. Is there a limit on how much epoxy resin I can mix at one time? The severity of the reaction varies depending on the individual and the amount of exposure. Our facilities will be closed from 12/31-1/7 so employees can spend time with their families. My past experience, I just usually toss them. MAS Deep Pour has a 5.5 hour gel time at 77°F in a 150 gram mass, but will set up much faster if warmer or left sitting for an extended time in a larger mass. Derek: Yes. You can tap the center and on the edges, you'll notice it'll be very gummy. In this demonstration, Derek from MAS Epoxy shows us how to prep, mix and pour Deep Pour epoxy into a large void. It cures within 24-36 hours at 21°C creating a clear, glass-like finish that resists yellowing and scratching with an extended … This also applies to recoating or touching up aged epoxy surfaces. Deep Pour is designed for casting in volume. .embed-container { Temperature:  Working in a shop or with material below 70F will cause the mixed epoxy to become too thick to properly release air and self level. Rob: All right. When you pour it, it's very clear and you will notice that all the bubbles will start to rise onto the surface and pop on their own. We are proud of the quality of our products, and we stand behind them 100%. That really does flow very, very smoothly, almost like water. Okay. Once mixed, how long is the working time? Best practice is to wait 5-7 days at room temperature for an epoxy surface to fully cure (develop it’s full mechanical and thermal properties) before putting it into service. We’ve also had great success with Gamblin Dry Pigments and Black Diamond powder mica pigments, both metallic and flat, to get a marbled or colored effect with the Table Top Pro epoxy. What about dyes? It's a brown Mixol, just a drop? Fully mixed:  Upon mixing, be sure to scrape sides and bottom of mixing container to ensure all resin and hardener are fully blended. Rob: Do you need to be worried about getting bubbles in it or anything at this point in time? We’ve run HDT on pretty much every competitor Table Top product on the market, and they are equal to or below MAS Table Top. Best practice to wait until epoxy is fully cured before putting into use. Scratch repair can be accomplished in two ways. – this is not the same as FDA approval. If the coffee cups have an uncoated ceramic bottom, you can actually scratch glass with that mug as well as virtually any room-temp cure epoxy surface. Do not mix more than one gallon at a time. Lastly, wipe clean with a cotton t-shirt rag and denatured alcohol. Mixed Table Top epoxy could also be diluted with roughly 2-5% denatured alcohol to help reduce mixed viscosity and improve self leveling in the affected area. Will epoxy resin bond or stick to acrylic? Periodically check for additional bubbles and remove as need. can potentially leave an impression on the surface. I just mixed according to the instructions and brushed on with a … deep. Compilation of pouring MAS Epoxy products in creative ways. What works well for one person, might not be the best approach for another. Everything's going to have some metallic shine to it, so some people will put it in a little bit of mica powder into their inks to kind of give it some more shine or glimmer, or flair I guess, but yes, you can mix colors to kind of create your own. What is the VOC Content of MAS Tabletop Pro? For the best experience on our site, be sure to turn on Javascript in your browser. Also check out Amazon.com, there are some unique options like glow in the dark or thermochromic pigment. Pouring:  NEVER scrape or brush the sides or bottom of the container you just mixed in to remove every last drop because no matter how thoroughly you may have mixed, there will always be an unmixed portion which can be dislodged and will leave a wet or sticky spot on your coating. The Ultimate Deep Pour Epoxy Resin 3" Pour Capacity | Demold in 24 Hours Shop Now. Temperature:  If the temp falls below 60°F while epoxy is initially setting up, it may stall out the chemical reaction needed to harden the epoxy. Does MAS Tabletop Pro have a strong odor? Whatever is left in this that cures, you can basically just squeeze the bucket and it'll pop right out in the form of that bucket, and you can just go ahead and reuse it. What causes bubbles in your epoxy resin finish? $39.99 Lastly, translucent dyes such as Transtint and Piñata Colors are also compatible with epoxy. Art work especially so. How can I remove fine scratches and swirl from epoxy resin? Cured epoxy is BPA-free, safer for food contact. How hot can MAS Deep Pour get during it's curing process? Best to soak up and/or scrape off as much material as you can with some rags first and then clean the affected areas with one of the options listed above. We don't have to tend to it, unlike other one-to-one systems where you would most likely need to torch every 10 minutes for a total of 30 minutes, but that should turn out pretty sweet. Derek: With deep pour, the thinner the layer, the longer it will take to cure since its mass and temperature-sensitive. The max thickness MAS Table Top Pro should be applied is 1/8-1/4” per layer. Surface prep is critical, if you can no longer make an indentation in the epoxy with your fingernail, then you are past the window for a chemical bond and will need to create a mechanical one. Derek: Another great thing about mixing with a drill is that, once this epoxy will harden on there, you can basically soak it in some denatured alcohol and just kind of stir it around in the coupling so, and then it will basically just pop right off and you'll be able to reuse it. Starting at I see about a bubble there. EcoPoxy Inc. is committed to creating, manufacturing, and distributing bio-based epoxies made from annually renewable resources and offer the world an alternative to traditional epoxy resins made from fossil fuels. MAS Table Top is not FDA approved for direct food contact. Rob: What's the first thing we need to do? a color changing temperature sensitive pigment so it might be blue then change purple. Next day cut a tic-tac-toe image into the epoxy with a shop knife. Derek: Well you can mix and match colors. For reference, a low VOC house paint may contain up to 50 g/L VOC and other VOC-exempt solvents. Apply heat to the ring with a heat gun or blow torch should release the ring without having to reapply completely. Some customers have had success using oil-based stain. If you must work with the epoxy resin in a confined space, wear a NIOSH approved respirator with an organic vapor cartridge. There’s certainly more than one way to go about this, and a whole lot of polishing compounds and equipment out there to choose from, but here’s a general description of a simple process you could try. Each layer MUST be allowed to cool to room temperature (70-80°F) before adding additional layers. We typically recommend using MAS Deep Pour epoxy for river tables where you can pour large amounts of epoxy up to 0.5-1” thick, and then using MAS Table Top Pro as the top coat. When working in conditions or with material below 70°F, epoxy resin may become too viscous to properly release air and self level. Rob: You mentioned, even though we're not going to do it, that this would have been a good place to use the penetrating and why is that? That way we can reuse it. It just depends on what availability you have, two plastic measuring cups, and things like that. MAS Table Top Pro has a hardness rating of 82 Shore D, and is resistant to scuffing and scratching under normal table wear and tear conditions. Thermochromic is interesting, its a color changing temperature sensitive pigment so it might be blue then change purple. All surfaces must be clean, dry and free of contamination. Lightly sand the surface and apply another coat to level it out. Step pour multiple layers for thicker castings. Some metals can tarnish quickly so it is a good practice to apply the epoxy shortly after prepping the surface. Pouring too thick and layering too quickly could cause the curing epoxy to heat up, yellow, distort or crack. Yes, you can already start to see the bubbles self-releasing on the center of this here. Now Mr. Power Mixer. The more you mix up, and the warmer it is, the faster it will gel. Objects that harder than the epoxy can scuff, gouge or scratch the surface if proper care isn’t given. The purpose of a seal coat is to minimize the effects of off gassing by creating a thin air-tight barrier between a porous wooden surface and the Table Top epoxy flood coat so air bubbles won’t percolate up through the curing epoxy creating cosmetic defects. Deep Pour Epoxy MAS Deep Pour Epoxy Resin System is a 100% solid, two-component, three to one by volume mix ratio formulated for deep pour casting, encapsulating and moulding applications. Best practice to wait until epoxy is fully cured before putting into use. What if I wanted to put streaks of color into some epoxies, how would I go about doing that? Do not over dilute. Items shipped directly from the manufacturer cannot be returned in store. 99. A little goes a long way. Exceeding max mixing quantity could cause MAS Table Top to generate excess heat, exotherm, smoke and then cure quickly inside your mixing bucket. Rob: We've used a few containers here. Epoxy is a temperature sensitive material. QT, Starting at Now, we get to pour. We'll basically shim it up the sides and then we can start mixing the epoxy. These are largely marketing claims that have not necessarily been substantiated. If it comes off easily without any wood chards then there is an adhesion problem and will not work, but if it comes off with bits of wood attached, the epoxy is penetrating the stain and will adhere well. This was actually designed for restoring and restructuring dry or rotted wood. I know that that's compatible with your system. When in doubt, use a cotton ball to test. From £ … Will epoxy resin change the color of wood? Touching up the machined indentations will be an important step to maintain a consistent clear high gloss finish. Also check out Amazon.com, there are some unique options like glow in the dark or thermochromic pigment. Instead of having to build layers of 1/4 inch thick use deep pour for deep casting IIT’S NAKED – ZERO VOCS And odor free for better air quality while you work – breathe easy while working with Naked Fusion. Clamp down the wood so it will not float when the epoxy is poured Derek: It's usually about four to six inches off the surface. Larger slabs should be poured thinner than smaller castings to minimize exotherm. So, we want to provide you with step by step instructions and video that shows you the process of building a live edge river table from start to finish. How much does the 1.3 gallon kit of MAS Deep Pour cover? We typically recommend using MAS Deep Pour where you can pour large amounts of epoxy up to 0.5-1” thick, and then using MAS Table Top Pro as the finish top coat. Happy New Years! However, it’s important to keep in mind that epoxy takes roughly 5-7 days at room temperature to fully cure and develop its full mechanical and thermal properties. The product should be stored indoors, on a raised surface off the floor and away from exterior walls. It cures slowly to a clear, glass-like finish that resists scratching and yellowing. Keep in mind, every project is unique. It would go a little bit more. Do not use a tack cloth. Take care to cover and seal any voids or cracks present. A 1.3 gallon kit of mixed Deep Pour (12.6 lbs), cast 1” thick, will have about a 260F peak exotherm, and a gel time of roughly 200 minutes. We had underestimated the amount of epoxy we would need because on the deep pour it actually floated the board and so we weren’t expecting to fully cover or encase the bottom also. Sanding might not be practical as this could scuff your diamond plate, so maybe just stick to degreasing with a clean cotton rag and acetone. Keep reading for all the steps and materials needed to build your […] When in doubt, small scale testing is always a good idea. Clean away sanding debris and solvent wipe with a clean cotton rag soaked in denatured alcohol. Keep in mind this procedure assumes a heavily scratch damaged surface, so you could start higher up in the sanding process if you choose: Volumetric yield of Deep Pour is about 25 cubic inches per mixed pound. Use caution for very large pours. Always apply a seal coat before flood coating. Degreasing the surface with acetone, abrading with 80 grit sandpaper and degreasing again with acetone before applying epoxy is the simplest method to improve the epoxy to metal bond strength. Be careful not to not over heat, scorch or burn the epoxy.